1/18/2024 0 Comments Download AutoMounteretc/autofs//file_tofs /mnt /etc/autofs/auto.file_server -timeout 60 /etc/autofs/auto.file_server foo -rw,soft,rsize=8192,wsize=8192 file_server:/srv/shared_dir Samba Single sharesĪdd the following to /etc/autofs/auto.master: ![]() To mount a NFS share for file_server on /srv/shared_dir at location /mnt/foo, add a new configuration, e.g. You can see the exported shares by typing: The -hosts option uses a similar mechanism as the showmount command to detect remote shares. automatically creating directory placeholders before mounting shares) is enabled by default although, AutoFS installation notes claim to remove that option from /etc/conf.d/autofs in order to start the AutoFS daemon. To enable automatic discovery and mounting of network shares from all accessible servers without any further configuration, you will need to add the following to the /etc/autofs/auto.master file: if /dev/sd" >/etc/autofs/auto.mntĪutoFS provides automatically discovering and mounting NFS-shares on remote servers (the AutoFS network template in /etc/autofs/ has been removed in autofs5). Removable devices are assigned block device locations according to the next available spot, e.g. When you are done configuring your templates (see below), launch the AutoFS daemon as root by enabling and starting the rvice.ĭevices are now automatically mounted when they are accessed, they will remain mounted as long as you access them. Open the file /etc/nf and add an entry for automount: To mitigate this, only use if you will always be connected to the share, and do not use your home folder or other commonly used folders lest your file browser reads ahead into the disconnected folder When trying to access the folder, programs will get locked into waiting for a response, and either the connection has to be restored or the process has to be forcibly killed before unmounting is possible. Note: This can cause problems with resources getting locked if the connection to the share is lost. home/user/usbstick -fstype=auto,async,nodev,nosuid,umask=000 :/dev/sdb1 etc/autofs/auto.master /- /etc/autofs/auto.template /etc/autofs/auto.template /path/to/folder -options :/device/path # ln -s /var/autofs/net/share_name /media/share_nameĪlternatively, you can have autofs mount your media to a specific folder, rather than inside a common folder. If you still want to automount to a target non-empty directory and want to have the original files available even after the dynamically loaded directories are mounted, you can use autofs to mount them to another directory (e.g. This procedure is however non-destructive, so if you accidentally automount into a live directory you can just change the location in auto.master and restart AutoFS to regain the original contents. The base directory will be mounted on to load the dynamically loaded media, which means any content in the base directory will not be accessible while autofs is on. The base directory will be created if it does not exist on your system. Setting this value to 0 will disable the timeout. It is important that you DO NOT change the drop-down option that says “Identify As” because, whats already in the box is the partition UUID matching the drive you selected in step 1 and 2, so there should be no need to change this option.Īfter checking the checkboxes and changing your mount point name, click “OK” and input your root pass to save the changes to fstab.Tip: The optional parameter timeout sets the amount of seconds after which to unmount directories. (these should be checked by default)Ĥb) Change the “Mount Point” to something you wish to identify the drive as… e.g /mnt/Backup In that window, after switching off “User Session Defaults”, the only two options I changed were…Ĥa) Make sure “Mount at system Startup” and “Show in user Interface” are both checked. WARNING: The options listed in this window directly edit the fstab file and should be modified with care the same as you would using the terminal. Link: How to Auto Mount Drives in Linux on Boot - YouTubeĪfter opening the application called “Disks”, select your desired drive on the left…Īfter selecting the drive On the right, select the correct partition on the drive you want to auto-mount.Ĭlick the check-mark to open the “Additional partition options” menu. Someone in the chat actually posted a comment with an easier solution I found much simpler. I had a second drive which wasn’t mounting after a boot automatically and I followed the video below and was able to get it to work.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |